Objective To design customized titanium alloy lunate prosthesis, construct three-dimensional finite element model of wrist joint before and after replacement by finite element analysis, and observe the biomechanical changes of wrist joint after replacement, providing biomechanical basis for clinical application of prosthesis. Methods One fresh frozen human forearm was collected, and the maximum range of motions in flexion, extension, ulnar deviation, and radialis deviation tested by cortex motion capture system were 48.42°, 38.04°, 35.68°, and 26.41°, respectively. The wrist joint data was obtained by CT scan and imported into Mimics21.0 software and Magics21.0 software to construct a wrist joint three-dimensional model and design customized titanium alloy lunate prosthesis. Then Geomagic Studio 2017 software and Solidworks 2017 software were used to construct the three-dimensional finite element models of a normal wrist joint (normal model) and a wrist joint with lunate prosthesis after replacement (replacement model). The stress distribution and deformation of the wrist joint before and after replacement were analyzed for flexion at and 15°, 30°, 48.42°, extension at 15°, 30°, and 38.04°, ulnar deviation at 10°, 20°, and 35.68°, and radial deviation at 5°, 15°, and 26.41° by the ANSYS 17.0 finite element analysis software. And the stress distribution of lunate bone and lunate prosthesis were also observed. Results The three-dimensional finite element models of wrist joint before and after replacement were successfully constructed. At different range of motion of flexion, extension, ulnar deviation, and radial deviation, there were some differences in the number of nodes and units in the grid models. In the four directions of flexion, extension, ulnar deviation, and radial deviation, the maximum deformation of wrist joint in normal model and replacement model occurred in the radial side, and the values increased gradually with the increase of the range of motion. The maximum stress of the wrist joint increased gradually with the increase of the range of motion, and at maximum range of motion, the stress was concentrated on the proximal radius, showing an overall trend of moving from the radial wrist to the proximal radius. The maximum stress of normal lunate bone increased gradually with the increase of range of motion in different directions, and the stress position also changed. The maximum stress of lunate prosthesis was concentrated on the ulnar side of the prosthesis, which increased gradually with the increase of the range of motion in flexion, and decreased gradually with the increase of the range of motion in extension, ulnar deviation, and radialis deviation. The stress on prosthesis increased significantly when compared with that on normal lunate bone. Conclusion The customized titanium alloy lunate prosthesis does not change the wrist joint load transfer mode, which provided data support for the clinical application of the prosthesis.
ObjectiveTo compare the strength difference between the interfacial screw and the interfacial screw combined with bone tunnel crossing technology to fix the tibial end of ligament during anterior cruciate ligament (ACL) reconstruction through the biomechanical test.MethodsTwenty fresh frozen pig tibia were randomly divided into two groups (n=10) to prepare ACL reconstruction models. The graft tendons in the experimental group were fixed with interfacial screw combined with bone tunnel crossing technology, and the graft tendons in the control group were fixed with interfacial screw. The two groups of specimens were fixed in the high-frequency dynamic mechanics test system M-3000, and the length change (displacement), ultimate load, and stiffness of graft tendons were measured through the reciprocating test and load-failure test.ResultsThe results of reciprocating test showed that the displacement of the experimental group was (3.06±0.58) mm, and that of the control group was (2.82±0.46) mm, and there was no significant difference between the two groups (t=0.641, P=0.529). The load-failure test results showed that the stiffness of the experimental group and the control group were (95.39±13.63) and (91.38±14.28) N/mm, respectively, with no significant difference (t=1.021, P=0.321). The ultimate load of the experimental group was (743.15±173.96) N, which was significantly higher than that of the control group (574.70±74.43) N (t=2.648, P=0.016).ConclusionIn ACL reconstruction, the fixation strength of tibial end with interface screw combined with bone tunnel crossing technology is obviously better than that of interface screw alone.
ObjectiveTo summarize the research progress of killer turn in posterior cruciate ligament (PCL) reconstruction.MethodsThe literature related to the killer turn in PCL reconstruction in recent years was searched and summarized.ResultsThe recent studies show that the killer turn is considered to be the most critical cause of graft relaxation after PCL reconstruction. In clinic, this effect can be reduced by changing the fixation mode of bone tunnel, changing the orientation of bone tunnel, squeezing screw fixation, retaining the remnant, and grinding the bone at the exit of bone tunnel. But there is still a lack of long-term follow-up.ConclusionThere are still a lot of controversies on the improved strategies of the killer turn. More detailed basic researches focusing on biomechanics to further explore the mechanism of the reconstructed graft abrasion are needed.
Objective To investigate the feasibility of anterolateral approach for L5 vertebral resection, bone grafting, and screw rod fixation by imaging and biomechanics researches. Methods Twenty formalized adult cadavers (12 males and 8 females) were randomly divided into 2 groups; L5 vertebral resection, bone graft, and screw rod fixation was performed on 10 specimens by using anterolateral approach (experimental group), and on the other 10 specimens by combined anterior and posterior approach. CT scanning and three-dimensional reconstruction were performed in the experimental group; preoperative maximal safe entry angle and depth of screws and intraoperative actual entry angle and depth of screws were measured; the sacral screw position was observed after operation. The biomechanical test was done in 2 groups. Results Twenty specimens smoothly underwent L5 excision and reconstruction. CT scan showed that there was no significant difference in maximal safe entry angle and depth of screws between males and females in experimental group before operation (P>0.05); the maximal safe entry angle and depth were 51.93° and 47.88 mm for anterior screw, and were 37.04° and 46.28 mm for posterior screw. After operation, depth of the sacral anterior and posterior screws were appropriate, which did not pierce into the spinal canal. The biomechanical test results indicated that the flexion, extension, and lateral flexion displacements, and vertical compression stiffness showed no significant difference between 2 groups (P>0.05). Conclusion For L5 lesions not invading posterior column, to use L5 vertebral resection, bone graft, and screw rod fixation by anterolateral approach is a safe and feasible method to reconstruct lumbosacral stability, with the advantages of no changing posture, less operation time and incision, and prevention of bone graft shift, but effectiveness need further be identified.
Objective To review the research progress of pathological changes of glenohumeral capsule in patients with recurrent shoulder anterior dislocation (RSAD). Methods The literature on shoulder capsules, both domestic and international, was reviewed. The anatomy, histology, and molecular biology characteristics of the glenohumeral capsule in RSAD patients were summarized. Results Anatomically, the glenohumeral capsule is composed of four distinct parts: the upper, lower, anterior, and posterior sections. The thickness of these sections is uneven, and the stability of the capsule is further enhanced by the presence of the glenohumeral and coracohumeral ligaments. Histologically, the capsule tissue undergoes adaptive changes following RSAD, which improve its ability to withstand stretching and deformation. In the realm of molecular biology, genes associated with the regulation of structure formation, function, and extracellular matrix homeostasis of the shoulder capsule’s collagen fibers exhibit varying degrees of expression changes. Specifically, the up-regulation of transforming growth factor β1 (TGF-β1), TGF-β receptor 1, lysyl oxidase, and procollagen-lysine, 2-oxoglutarate 5-dioxygenase 1 facilitates the repair of the joint capsule, thereby contributing to the maintenance of shoulder joint stability. Conversely, the up-regulation of collagen type Ⅰ alpha 1 (COL1A1), COL3A1, and COL5A1 is linked to the recurrence of shoulder anterior dislocation, as these changes reflect the joint capsule’s response to dislocation. Additionally, the expressions of tenascin C and fibronectin 1 may play a role in the pathological processes occurring during the early stages of RSAD. ConclusionGlenohumeral capsular laxity is both a consequence of RSAD and a significant factor contributing to its recurrence. While numerous studies have documented alterations in the shoulder capsule following RSAD, further research is necessary to confirm the specific pathological anatomy, histological, and molecular biological changes involved.
The stress distribution and different abduction angles have a close relation to the hip joint. The purpose of this study is to provide biomechanical evidence for the treatment or precaution of hip joint injuries. A three-dimensional model of the hip was established through a series of processing based on the normal human hip joint computed tomograph (CT) image data which were applied to reverse engineering software Mimics14.0 in this study. Firstly, a three-dimensional finite element model was generated with meshing and assigned material and then it was imported into the finite element analysis software Ansys13.0. At last the stress at the femoral neck was solved, computed and analyzed in the positive orthostatic position with 7 hip abduction angles of the hip joint: 0°, 5°, 10°, 15°, 20°, 25°, and 30°, respectively. The results showed that the stresses of femoral neck and outer region were obviously higher than those of front and rear area of the neck of femur in the upright position or abduction of a different angle. With the increase of abduction angle, femoral neck in front of the regional stress value basically unchanged and rear area decreased, but the more obvious changes occurred in the outer region although the stress of inner and outer area also increased gradually. The hip abduction may cause changes in stress distribution because of the femoral neck stress mostly concentrated in the inner and outer cortex, and therefore it has an important role in guiding for hip surgery injury patients to choose the most reasonable solutions and prevention initiatives.
Objective To compare the biomechanical properties of two ultra-strong sutures and suturing methods in panda rope bridge technique (PRBT) application, and provide guidance for clinical selection of suture threads and suture methods. Methods Forty Achilles tendons from bulls were randomly divided into 4 groups (n=10) and transected at the 4 cm proximal to the tendon insertion. Groups A and B used Ethibond sutures (USP 5), the proximal end was fixed at the myotendious junction with Krackow sutures and the distal end was fixed through a calcaneus canal. Groups A and B had 4 and 8 threads through the stump plane, respectively. Groups C and D used Ultrabraid sutures (USP 2), the proximal end was fixed at the myotendious junction with Krackow sutures and the distal end was fixed in the calcaneus with two anchors. Groups C and D had 4 and 8 threads through the stump plane, respectively. The dynamic tensile forces of 20-100, 20-200, 20-300, and 20-400 N were tested respectively by using a dynamic tensile testing machine at 0.5 Hz for 250 cycles. After each stage of testing, the gap between stumps was measured with a caliper and the type of suture failure was recorded. Results After dynamic tensile forces of 20-100 N and 20-200 N, the gaps of the four groups arranged from small to large were groups D, B, C, and A. The differences between groups A and B and groups C and D were significant (P<0.05). But after dynamic tensile forces of 20-300 N and 20-400 N, the gaps were more than 5 mm in all groups. The suture retention rates of the four groups after dynamic tensile forces of 20-100 N and 20-200 N were all 100%. The suture retention rates of groups A, B, C, and D were 0, 80%, 60%, and 100%, respectively after dynamic tensile forces of 20-300 N. The differences of suture retention rates between group A and groups B and D were significant (P<0.05). There was no significant difference between groups B, C, and D (P>0.05). After dynamic tensile forces of 20-400 N, the suture retention rates of groups A, B, C, and D were 0, 50%, 0, and 70%, respectively. There were significant differences between groups A and B and groups C and D (P<0.05). Conclusion Repairing Achilles tendon rupture via PRBT with 8 ultra-strong sutures through the stump plane can meet the mechanical requirements for walking by using ankle boots and heel pads in the early accelerated rehabilitation after operation.
The anterior cruciate ligament (ACL) reconstruction mostly relies on the experience of surgeons. To improve the effectiveness and adaptability of the tension after ACL reconstruction in knee joint rehabilitation, this paper establishes a lateral force measurement model with relaxation characteristics and designs an on-line stiffness measurement system of ACL. In this paper, we selected 20 sheep knee joints as experimental material for the knee joint stability test before the ACL reconstruction operation, which were divided into two groups for a comparative test of single-bundle ACL reconstruction through the anterolateral approach. The first group of surgeons carried out intraoperative detection with routine procedures. The second group used ACL on-line stiffness measurement system for intraoperative detection. After that, the above two groups were tested for postoperative stability. The study results show that the tension accuracy is (? 2.3 ± 0.04)%, and the displacement error is (1.5 ± 1.8)%. The forward stability, internal rotation stability, and external rotation stability of the two groups were better than those before operation (P < 0.05). But the data of the group using the system were closer to the preoperative knee joint measurement index, and there was no significant difference between them (P > 0.05). The system established in this paper is expected to help clinicians judge the ACL reconstruction tension in the operation process and effectively improve the surgical effect.
ObjectiveTo evaluate the biomechanical effect of a nickel-titanium (Ni-Ti) three-dimensional memory alloy mesh in treating a canine tibial plateau collapse fracture model and to lay a foundation for further experiments in vivo.MethodsSixteen tibial plateau specimens of 8 adult Beagle dogs were harvested. Twelve specimens were taken to prepare canine tibial plateau collapse fracture models (Schatzker type Ⅲ) and randomly divided into groups A, B, and C, with 4 specimens in each group. Four normal tibia specimens were used as blank control group (group D). In groups A and B, the bone defects were repaired with Ni-Ti three-dimensional shape memory alloy mesh combined with autologous bone and simple autologous bone respectively, and fixed with the lateral plate and screw. In group C, the bone defect was directly fixed with the lateral plate and screw. By using a biomechanical tester, a progressive load (0-1 700 N) was loaded vertically above the femoral condyle. The maximum failure load was recorded and the stiffness was calculated according to the load-displacement curve.ResultsThe maximum failure loads in groups A, B, C, and D were (1 624.72±7.02), (1 506.57±3.37), (1 102.00±1.83), and (1 767.64±24.56) N, respectively; and the stiffnesses were (129.72±20.83), (96.54±27.05), (74.96±17.70), and (169.01±35.62) N/mm, respectively. The maximum failure load and stiffness in group A were significantly higher than those in groups B and C, but which were significantly lower than those in group D (P<0.05).ConclusionNi-Ti three-dimensional memory alloy mesh combined with autologous bone can repair the Schatzker type Ⅲ tibial plateau collapse fracture, which has better biomechanical properties than simple autologous bone grafting.
ObjectiveTo compare the biomechanical characteristics of self-made nickel-titanium shape memory alloy stepped plate with calcaneal plate and cannulated compression screws in fixing calcaneal osteotomy.MethodsCalcaneal osteotomy was operated on 6 fresh-frozen lower limbs collected from donors. Then three kinds of fixation materials were applied in random, including the self-made nickel-titanium shape memory alloy stepped plate (group A), calcaneal plate (group B), and cannulated compression screws (group C). Immediately after fixation, axial loading of 20-600 N and 20 N/s in speed was introduced to record the biomechanical data including maximum displacement, elastic displacement, and maximum load. Then fatigue test was performed (5 Hz in frequency and repeat 3 000 times) and the same axial loading was introduced to collect the biomechanical data. Finally, the axial compression stiffness before and after fatigue test were calculated.ResultsThere was no significant difference in the axial compression stiffness between pre- and post-fatigue test in each group (P>0.05). However, the axial compression stiffness was significant higher in group A than that in groups B and C both before and after fatigue test (P<0.05). No significant difference was found between group B and group C (P>0.05).ConclusionSelf-made nickel-titanium shape memory alloy stepped plate is better than calcaneal plate and cannulated compression screws in axial load stiffness after being used to fix calcaneal osteotomy.