Objective To discuss the improved method and effectiveness of posterior pedicle-screw fixation combined with restoring and grafting through the injured vertebrae for treating thoracolumbar burst fracture. Methods Between March 2008 and September 2010, 21 patients with thoracolumbar burst fracture were treated by posterior pedicle-screw fixationcombined with restoring and grafting through the injured vertebrae. Of 21 cases, 15 were male and 6 were female with an age range of 20-61 years (mean, 38.4 years). Affected segments included T12 in 5 cases, L1 in 7 cases, L2 in 5 cases, and T12-L1 in 4 cases. According to Frankel classification for neurological function, 2 cases were rated as grade A, 4 cases as grade B, 6 cases as grade C, 5 cases as grade D, and 4 cases as grade E; based on Denis classification, all 21 cases were burst fractures, including 7 cases of type A, 11 cases of type B, and 3 cases of type C. The X-ray film was taken to measure the relative height of fractured vertebrae and Cobb’s angle, and the function of the spinal cord was evaluated at preoperation, postoperation, and last followup. Results All the incisions healed primarily. The 21 patients were followed up 12-30 months (mean, 26 months). No loosening or breakage of screws and rods occurred. X-ray films showed good bone heal ing with the heal ing time from 12 to 23 months (mean, 16 months). The Cobb’s angles at 1 week and 1 year postoperatively were (3.4 ± 2.4)° and (5.2 ± 3.2)° respectively, showing significant differences when compared with preoperative angle (22.1 ± 1.2)° (P lt; 0.05), while no significant difference between 1 week and 1 year after operation (P gt; 0.05). The anterior height of injured vertebrae recovered from (14.6 ± 2.1) mm (40.2% ± 1.5% of the normal) at preoperation to (36.0 ± 2.0) mm (95.3% ± 1.3% of the normal) at 1 week, and to (35.0 ± 2.4) mm (94.4% ± 2.5% of the normal) at 1 year; significant differences were found between preoperation and postoperation (P lt; 0.05), while no significant difference between 1 week and 1 year after operation (P gt; 0.05). At 1 year after operation, the Frankel neurological function grade was improved in varying degrees, showing significant difference when compared with preoperative grade (χ2=11.140, P=0.025). Conclusion Improved method of posterior pedicle-screw fixation combined with restoring and grafting through the injured vertebrae in treatment of thoracolumbar burst fracture can reconstructthe anterior and middle column stabil ity and prevent loss of Cobb’s angle and height of vertebrae.
【摘要】目的探討經腹腔入路一期病灶清除、自體髂骨移植、后路椎弓根固定治療腰骶椎結核的效果。方法對2004年8月2007年6月收治12例L4～S1椎體結核,采用經腹腔入路顯露腰骶椎,徹底清除病灶后用自體髂骨塊椎間植骨,后路椎弓根螺釘固定;術后常規支持和抗結核治療,術后1、3、6、9、12個月,以后每6個月一次定期隨訪,觀察血沉變化,攝X線片、CT三維重建評估結核活動、骨塊融合和畸形矯正情況。結果術中無大血管、神經、輸尿管損傷,隨訪11～23個月,平均17個月,結核病變局部無復發,無結核性腹膜炎、性功能障礙等并發癥發生。結論經腹腔前方入路暴露腰骶椎結核病灶充分、安全,病灶清除后行自體髂骨塊椎間植骨、腰骶椎后路椎弓根螺釘固定可有效重建腰骶椎的穩定性。
Objective To investigate the effectiveness of sacroiliac screw implantation assisted by three-dimensional (3D) printed faceted honeycomb guide plate in the treatment of posterior pelvic ring fracture. Methods The clinical data of 40 patients with posterior pelvic ring fractures treated with sacroiliac screw implantation between December 2019 and December 2022 were retrospectively analyzed. Among them, 18 cases were treated with sacroiliac screws fixation assisted by 3D printed faceted honeycomb guide plate (guide plate group), and 22 cases were treated with sacroiliac screws percutaneously fixation under fluoroscopy (conventional group). There was no significant difference in baseline data (P>0.05) such as gender, age, time from injury to operation, and Dennis classification between the two groups. The implantation time, frequency of C-arm X-ray fluoroscopy, frequency of guide pin adjustment of each sacroiliac screw, and postoperative complications and bone healing were recorded. Majeed score was used to evaluate the functional recovery at 6 months after operation, and CT was used to observe whether the screw penetrated the bone cortex. The deviation between the virtual position and the actual position of the screw tip, the sacral foramen, and the screw entry point was measured on the sagittal CT images of the guide plate group. Results The number of screws implanted in S1 and S2 vertebral bodies was 14 and 16 respectively in the guide plate group, and 17 and 18 respectively in the conventional group. The implantation time of each sacroiliac screw, the frequency of C-arm X-ray fluoroscopy, and the frequency of guide pin adjustment in S1, S2, and all vertebrae in the guide plate group were significantly less than those in the conventional group (P<0.05). Patients in both groups were followed up 8-48 months, with an average of 19.7 months. There was no incision infection, screw displacement, or internal fixation loosening in both groups. Callus growth was observed in all patients at 12 weeks after operation, and bone healing was achieved in all patients. The healing time ranged from 12 to 24 weeks, with an average of 15.7 weeks. No sacroiliac screw penetrated the bone cortex in the guide plate group; 2 patients in the conventional group had sacroiliac screws penetrating the bone cortex without damaging blood vessels or nerves. In the guide plate group, the deviation between the virtual position and the actual position of the screw tip, the sacral foramen, and the screw entry point were (2.91±1.01), (2.10±0.74), and (1.67±0.70) mm, respectively, with an average deviation of (2.19±1.22) mm. There was no significant difference in Majeed function evaluation between the two groups at 6 months after operation (P>0.05). Conclusion The application of 3D printed faceted honeycomb guide plate in sacroiliac screw implantation for posterior pelvic ring fracture can shorten the screw implantation time, reduce the frequency of fluoroscopy and guide pin adjustment, and reduce the risk of screw penetration through the bone cortex.